Project 10: Zoetrope

Homework 10: Zoetrope

For this project we are going to be making a Zoetrope. This will use some of the same pieces of the previous project as it uses the motors pinwheel but will give us control on the speed and direction of the motor. This project will utilize the H - bridge and IC that will help control the things we need for this project.





Coding 

The coding was a little more intensive since we ended up having a bit more inputs and outputs. Relatively it is just more variables since we check for speed directions and if it is on or off. Looks like it is more complex but is pretty simple if you break it down. 









Finished Product

This was simple and fun and my tape job from the previous project came back to bite me. On the pinwheel because you need to attach more pieces there are four stills so that can be done. My tape made it so they stuck together so it was fun trying to get the support in it. Otherwise, assembly was simple. This time there are two videos to show the different directions. 



Forward



Backwards



Comments

Post a Comment

Popular posts from this blog

Personal Project 3: Etch A Sketch

Image
  Etch-A-Sketch I needed to make something with the arduino and something art related. So with two knobs and a screen to draw on I thought I could recreate the etch a sketch. The etch a sketch would fulfill the requirements and a fun little thing to make. Initial Setups This is the initial build I used for my testing to make sure that I can get different values for each potentiometer and a value from the tilt sensor. .  This was the code I used to get the initial reads and would make sure that I would be sending the proper data. I did come across an issue here with the mapping and have it solved later. My unity was a blank 2d core and I created a small square prefab.  This is my final setup and parts list. The values i got from the potentiometer were correct and the sensor would detect when tilted. Final Coding Arduino: This was a total of 40 lines of code on the Arduino side. The delay is a little bit lower so that more will get drawn to the screen. I also had to do the map function
Read more

Personal Project 4: Clap Lights

Image
       Light Clap I needed to address an issue that could be solved with an Arduino. I went ahead with the idea of when you're in bed with the lights still on. So, with the use of sound, we can change the state of the Leds. I would have it programmed to work with a rgb strip but  Initial Setups This is the initial build I used for my testing to make sure that I can get my lights to light up and test to see if i can get values from the piezo.  This is the code I used to make sure the circuit worked, and all the lights lit up. I just used hard coded values for testing and would later change it to have only certain ones light up. This is my final setup and parts list. I successfully got the value to light the Leds up and the value from the piezo were in tolerance. Final Coding Arduino: I got the code together to make it have different states of lit up lights to replicate an RGB strip. The code was pretty simple. The code to make it so that the clap will change the states is the same
Read more

Personal Project 2: Tic Tac Toe

Image
  Tic Tac Toe I needed to make an alternative controller, so I made one for tic tac toe that is run in unity. I went with tic ta toe because I have the pieces to make it and the knowledge to do it. I went with unity due to past experience in the program. Initial Setups This is the initial build i used to test my buttons. This resistor ladder is just like the one used in project 7.  This was the code I used to get the initial reads and make sure that I am still getting the same results as the project 7.  This is what my unity sketch looks like. I made no real changes to it, just got rid of the circle in the top spot. I was using it to determine where the pieces were going to go. This is my final setup and parts list. The double resistor ladder on each side of the board was nice and can be used with further coding for other things. Final Coding Arduino: There is a lot of coding, but it is mostly just simple stuff of just checking if the value is what we want and the printing the data t
Read more